Sunday, August 31, 2014

HOW TO CORRECT ELECTRICAL TERMINAL ROLL

terminal stopkontak / terminal rol listrik
The increasing number of electronic devices that we have made ​​the need for a wall outlet to grow, but this need not be balanced with the amount of available power outlet, while for installing new power lines that permanent was not possible.

That is why many people look for other, more practical alternatives without having to install or connect the cable, one is to buy a roll cable terminal. With this tool we simply connect the plug into an existing outlet in the house, then roll live retractable cord as needed and can be directly used.

Generally there are four outlet that is attached to a cable box and a roll indicator light will illuminate when power is connected from the plug to the cable.

Damage that often occurs on a roll of electrical terminals

     Total dead, electricity does not flow to the outlet terminal on the cable roll even though the plug has been plugged into a wall outlet, this can be seen with the extinction of the indicator lights are located on the cable near the terminal roll.
     Outlet at the terminal roll can not be used, but the indicator light,
     Supplied to the electrical terminals sometimes roll dead sometimes alive, it is characterized by the death of indicator light turns on and turns.

For more details on how to repair the damaged cable terminal roll please refer to the explanation below.

Total dead,

Electricity does not flow to the outlet terminal on the cable roll even though the plug has been plugged into a wall outlet, this can be seen with the extinction of the indicator lights are located on the cable near the terminal roll ..

How to fix;
    bagian dalam kotak terminal rol listrik
  1. Open an existing screw on the terminal and then separate outlet / outlet cover lift.
  2. look at all parts contained in the cable box roll, if both cables are firmly connected to the terminal outlet? when plugged in then it is likely path to the plug wires from the terminal there are broken.
  3. To determine whether the cable is broken or not, can be tested using testpen or AVO meters
With testpen:
    cara mengukur dengan tespen
  1. insert the plug into the outlet, press the switch on the terminal roller to position "on"
  2. insert the tip into the hole in the terminal testpen electric rollers, do this test in all holes.
  3. If there are no holes that can turn tespen try to pull the plug and then insert the plug into an outlet with reversed position (rotated 180derajat),
  4. Repeat the measuring terminals on a roll as before (point 2), when tespen still not illuminated, you can bet both wires breaking inside, but when tespen be lit on one luibang then only one cable is disconnected inside.
R X 1 KWith Avo meter:
    cara mengukur jari steker
  1. Disconnect the plug from the socket
  2. Set the selector switch position on avo meter on a scale of 1 Kilo Ohm RX,
  3. Paste one of the probes (measuring stick) on AVO meter to plug one finger while the other probe to one of the outlet hole
  4. Cable is still good / connected will be indicated by the movement of the needle on the AVO meter in the right direction and still in zero.
  5. while the cable is disconnected will be marked with no movement of the needle on the AVO meter.
  6. Repeat the measurement sequence on the cable and plug the other outlet hole as above to determine whether the cable is disconnected as well or not.

cara mengukur lubang terminal pada rol listrikHow to find the location of the cable is disconnected without using testpen or AVO meter:

This method can only be done on breaking the cable side.

  1. Insert the plug into the outlet
  2. Turn on the power roller terminal by changing the position of the switch to the "on"
  3. Begin to bend-bent wires start from the base of the plug to the cable end closest to the terminal box while
    location of the needle is still in the avo
    attention to the indicator lights on the terminal box roller.
  4. When the bend-bent wires when the light turns on and off alternately in the cable means that we bend the cables are connected by bending breaking us,
  5. Peel off the wrapper and check the cable where the cable is broken.
  6. Having found where the wires are broken then connect the cable that broke up correctly
  7. When the location of the cable that broke near the plug so as not to allow the plug to be connected then attach the new
    letak jarum avo pada angka nol
    at the end of the cable.
If the above does not work then you can use the "original guess" which way is done by cutting the cable, this is done by way of a sequential manner, namely:
  1.  Cut the cable with a length of approximately 50cm from the plug,
  2. Measure the respective wires to the terminal box using AVO meter roll with RX 1Kohm,
    cara menekuk kabel
  3. Attach one probe to one of the cable while the other probe to one of the holes on the terminal power roller, a good cable is indicated by the movement of the needle to the right avo, sedamgkan cables breaking is indicated by no movement of the needle avo.
  4. If the above test is still no wires are broken then do a second cutting by cutting along the 50cm cable and repeat testing at point 2 and point 3.
  5. do the above test is not found again until the cable
    roll of electrical wires that have replaced the plug
    who dropped out, usually that cables that broke is the closest to the plug wires because the wires that move frequently pulled and stretched so that the cable can be dropped inside.
  6. If you do not have the AVO meter to measure the cable then attach the new plug on the cord is cut and then connect the new plug in the wall socket and see the indicator light on the terminals of electric rollers, roller terminals when the power is on means that the cable is correct, but when the indicator light is off then disconnect plug and cut again along the 50cm cable and do a retest.
Outlet at the terminal roll can not be used, but the indicator light, and electricity flowing to the electrical terminals sometimes roll dead sometimes alive, it is characterized by the death of the indicator light turns on and turns.

How to fix:
    plat yang longgar
  1. Not the screw on the top of the terminal and then lift and turn the terminal so visible underneath.
  2. Check the connection cable and plug finger clamp plate.
  3. Clean the rust that is usually attached to the plate using sandpaper.
  4. see also form if plate clamp plate clamp capable of clamping any plug that goes, if the plate looks loose then fix it by clamping pliers receipts.
  5. If you do not have the tang then you can use the index finger and thumb to clamp the plate to return to its original position so as to clamp the plug finger.
  6. Replace all components and then try connecting the power cord to the wall socket and roll Test it one electrical outlet on a roll with memasaukkan electronic appliance plug into the wall outlet, if the electronic equipment repair light means we can succeed.
cara memperbaiki plat dengan jari

No comments:

Post a Comment